![]() We cannot nor will not guarantee they meet any regulations out of the United States as every country has their own regulations. ***Note: These bottles are only date certed. (1) 80PSI Regulator with Bottle Pressure Gauge.(1) Sensor T (Male, Female, Female) 1/8" NPT for Dome Pressure Sensor on Wastegate.(1) Nickel Plated Push to Connect T Fitting.(3) Straight Nickel Plated Push to Connect 1/8" NPT Fittings.(6) 90° Nickel Plated Push To Connect 1/8" NPT Fittings.This is a very standard fitting size across brands such as Tial, JGS, Precision, Turbosmart, Procharger, and many others. Our nickel plated fittings are 1/8 NPT which work with nearly every brand wastegate, blow off valve, and solenoid on the market. The CO2 regulator comes preset at 80 psi which is appropriate for nearly every setup (the boost controller regulates pressure down from there). There are enough fittings in this kit to plumb the following: This all inclusive kit comes with top quality fittings, regulator, line, and bottle to plumb any Boost Controller system on the market. The Motion Raceworks Single Turbo CO2 Kit takes the guess work out of fittings. motionraceworks ABC, as easy 1, Co2, 3 - we have stamped dated bottles, all the accessories you could need, and full single or twin wastegate kits. Mount CO2 regulator as close as possible to air cylinder for proper function, any length away adds delay and possible incomplete release.Motion Raceworks SINGLE Wastegate Turbocharged CO2 Kit C02 Handle Release is meant to operate at conditions of 80 psi and higher, the higher the PSI the faster and better the function of this system. The Motion Raceworks Single Turbo CO2 Kit takes the guess work out of fittings. Cable needs to have loose swooping bends, failure to test beforehand/and or constrictive bends can cause this handle to operate slower or incorrectly. Note: Please test operation prior to going to the racetrack. Improper Installation, hookup, or misuse may result in improper function of this part. The biggest thing is you need to TEST this before heading to the track. Please note that even though this kit is meant to be a complete kit, and has been strenuously tested, refined, and appropriately changed to work under demand of today’s chassis, care needs to be taken when installing. Our design of this kit was made to operate under 80 psi, though, it operates better the higher you go up to 120psi. ![]() When installed properly this release kit will make for simple, reliable, release of your parachute while keeping both hands firmly planted on the wheel. Available in both single and dual cable styles. We spent a ton of time designing, redesigning, and perfecting this kit. CO2 Solenoid Weld or Clamp on mounting bracket.Cable with necessary connection hardware.Our kit is designed to WELD OR CLAMP on and provides a complete solution with no guess work or any additional fabrication. Motion Raceworks is a solution provider for EFI, Boosted, and Late Model Vehicles both on and off the track. Comes with bottle pressure gauge and 1/8' NPT port to screw your fitting into. When it is most important to pay attention to the track and things are moving fast, launch your parachute with the push of a button rather than taking your hand off and trying to find a handle mounted above/out of the way of eyesight. 109.00 Starting at 9 /mo with Prequalify Now Quantity Add to cart Add to Wishlist Dual Adjustable CO2 Regulator w/ Gauge 25005 This Dual CO2 Adjustable regulator screws right on to your CO2 bottle with standard nut. The Motion CO2 Release handle kit is the answer to keeping your hands on the wheel at the big end of the track. ![]() Motion Raceworks Billet CO2 Activated Parachute Handle Release Lever & Cable Mount Kit ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |